How To Remove The Gas Tank From A Briggs & Stratton Lawn Mower

Have you lot always found the gas tank of your Briggs and Stratton lawnmower to exist leaking fuel? Or were you concerned virtually the buildup of old fuel deposits within the tank? To set up these issues, you have to remove the gas tank from the mower's body and perform a further inspection. If you aren't certain how you should remove the tank from a Briggs and Stratton lawnmower, this article will have you through a stride-by-step approach.

How to remove the gas tank from a Briggs and Stratton lawnmower, step-past-step:

Step 1. Gather the necessary tools and disconnect the spark plug wire from the plug itself
Pace two. Empty the gas tank
Pace iii. Detach the fuel lines that originate from the tank
Stride 5. Accept the gas tank off from the mower'due south body by removing the mounting screws
Step v. Protect the fuel lines to forbid the entry of dust into the carburetor

The Gas tank is fuel storage designed to keep the fuel clean, secure, and properly vented. The tank is made up of corrosion-resistant materials so that the corrosive nature of water and ethanol can exist nullified. Occasionally, you might hit your lawnmower against a hard object that can cause some damage to the gas tank. When gas is kept in a gas tank for an extended fourth dimension, it tin can likewise dethrone and clog the tank'south vents. For all these reasons, you have to remove the tank starting time to assess the impairment and get it repaired or replaced.

Please stay tuned as we provide you with a very comprehensive and pace-past-step guide for removing the gas tank on a Briggs and Stratton lawnmower.

Contents

i General Troubleshooting Guide:
- 1.1 ● Footstep ane. Gather the necessary tools and disconnect the spark plug cables
- i.2 ● Pace 2. Empty the gas tank
- 1.3 ● Step 3: Remove the connections to the gas tank
- 1.iv ● Footstep 4: Remove the gas tank
- 1.5 ● Step v: Protect the fuel lines to foreclose the entry of grit into the carburetor
2 Some rubber tips
3 Often asked questions:
- 3.ane 1. How exercise y'all clean a gas cap on a lawnmower?
- 3.2 2. What happens if air bubbles arrive your gas tank?
- iii.3 three. How to open fastening bolts that are rusted or locked?
- 3.4 iv. Is information technology preferable to repair a gas tank instead of replacing it?
4 Terminal remarks:

General Troubleshooting Guide:

To remove the gas tank from your Briggs and Stratton lawnmower, you tin can use the following steps. It is ever advisable to have some pictures or brand a small video of how the various parts are continued. So when you take to reattach them, yous can use them to know how each component is connected.

● Stride 1. Assemble the necessary tools and disconnect the spark plug cables

Removing the gas tank is non a difficult taks. You will need tools like:

Fuel line clamps to agree the flow of fuel.
An adjustable wrench to remove the fasteners.
A siphon pump or empty gas container to drain the gas from the mower.
A pair of condom gloves.

Disconnect the spark plug wire from the spark plugs. This is a precaution to prevent the engine from unintentional starting. Besides, turn the ignition off.

● Pace two. Empty the gas tank

Ensure that the gas tank is empty before removing it from the Briggs and Stratton mower. Y'all can exercise this in 2 means. If at that place is only a minimal amount left, you lot can first the lawnmower and let information technology run until the fuel tank is empty. This will remove well-nigh of the gas in the tank, and there will merely exist a tiny amount left.

If there is more gas in the tank, you need to bleed information technology. Yous can carefully disconnect the fuel line for this. Or use a siphon pump to get the gas from the tank. Store it in a suitable container. If the gas is still ok, y'all can use it later.

● Step three: Remove the connections to the gas tank

The next pace is to remove the gas tank that is usually mounted on elevation of the engine trunk. As the fuel period requires, information technology lies close and at a height to the main engine. The first step is ensuring that your Briggs and Stratton mower is placed on apartment basis, such as that of a driveaway. If possible, park it on a floor that tin can bargain with some gas spillage. Engage the parking brakes if it's a riding lawnmower.

Now, remove the mower hood if your tank lay under it. In most cases, it lies externally. Next, you need to remove the connections that emerge from the tank. Typically, these tanks take one opening form where y'all cascade in the fuel, and they have ane get out line which supplies fuel to the combustion chamber.

Briggs and Stratton lawnmowers take only 1 fuel line to carry the fuel to the carburetor. The exit line has a hose fastened with fasteners or an adjustable tightening ring. Remove these fasteners to free the gas tank of any connections. You might have to remove a few seals and washers in doing then. Go along them prophylactic with y'all to use in the future.

● Step 4: Remove the gas tank

The gas tank usually has at least two mounting bolts on its base to connect it to the balance of the main body. With the help of an adjustable wrench, you lot tin easily loosen them by giving regular anti-clockwise twists. With this, you will have your removed gas tank with the fuel cap attached to its tiptop (if it has i).

● Footstep v: Protect the fuel lines to prevent the entry of dust into the carburetor

As a final pace, you must make certain that removing the gas tank doesn't leave the fuel lines bare open. Utilize a plastic sheet or cap to shut the unprotected fuel line that previously was connected with the tank. This will protect the Briggs and Stratton fuel line from any clay and debris buildup. Also, check if any components that were previously covered by the tank need to be protected.

Some safety tips

Before you operate or service your engine, always read the machine and equipment transmission to prevent holding damage or personal injury.

Take exteme care with gas: Fuel and the fumes of fuel are exceptionally explosive and inflammable. When working on the gas tank, keep all sources of spark and ignitions away.
Supersede or repair a damaged gas tank: Fuel tanks are made of corrosion-resistant fabric or glazed with a corrosion-resilient substance to withstand against harmful effects of alcohol, water, or salt. The tank should be replaced if it is damaged or corrupted. Use just recommended parts by the engine manufacturer if you are attempting to modify the tank.
Protect your easily: Use a pair of safety gloves when dealing with the engine body. These will protect yous from whatsoever harm.
Go on some fabric ready: Continue a few rugs of an quondam cloth close past whenever draining the gas tank.

The following is a link to remove the gas tank from a craftsman lawnmower. It is quite like to a Briggs mower in terms of the steps involved.

Frequently asked questions:

1. How practice you clean a gas cap on a lawnmower?

Gas-powered lawnmowers can operate in rough outdoor environments. Dissimilar parts like the cap of the gas tank can go dirty. Use a dry fabric piece and to remove the clogged debris or dirt. You can so use the same cloth piece to make clean the cap properly later dipping it in a chip of petrol. And brand certain that the modest hole in the gas cap is open. This is needed to permit air in the tank when gas is used.

2. What happens if air bubbles get in your gas tank?

The gas tank supplies fuel to the combustion chamber. Sometimes, the flow lines may get chock-full, creating a surge of air or drop of pressure in the tank. If a bubble of air gets trapped in the tank, it can make the engine run poorly. The air bubbles from the tank will eventually catamenia in the fuel lines. This can pb to delaying the showtime, or hiccupping may occur. It can even cause seizure bug if the air packet is too large and frequent. Usually, the engine takes a few jumps and and then recovers from information technology.

3. How to open fastening bolts that are rusted or locked?

The lawnmower is always working in harsh environments. The exposure to moisture may cause the nut bolts to corrode and get locked in their position. If yous are not careful with them, y'all might even break them. Here are a few solutions that you tin can endeavor:

Metal Plate: Try welding the locked nut bolt head to a metallic plate. This elongates the moment arm making it easier to twist it open.
File: You can apply a metallic file or ruler to create two perpendicular grooves on the commodities caput, making a cross. Yous can use a long screwdriver, which makes it easier to turn.
Cleaner spray: Sometimes, the problem can be solved as rapidly as throwing in some cleaner spray and letting it rest for a while.

iv. Is information technology preferable to repair a gas tank instead of replacing information technology?

It depends on the condition of the gas tank. They are made from quite sturdy and corrosion-resistant materials, only there is always a chance something happens with them. More often than not what may seem similar a crack is only a body scratch that looks likewise severe. If the gas tank is not leaking, and so it is e'er usable. If the damage is minor and tin can exist treated by welding, adhesives, or a special coating, yous tin try repairing it. Or let a professional repair information technology. If the condition is actually bad, or the fix simply works temporarily, you should replace it.

A gas tank ensures that the fuel stays clean and prevents it from degrading. Similar all other lawnmower components, a gas tank may require repairing or cleaning at some betoken in time. Hence, removing it might seem a hassle if y'all oasis't removed it before. Removing the tank is a relatively simple process but requires some small precautionary measures to keep the remainder of the components free from dirt. Past following the steps higher up and seeing the reference videos, you lot can smoothly perform this chore yourself.